Porsche 924S - Driver Door Trim Removal Photos

After Removing Trim

Cable which connects inner handle to locking mechanism

2015 Footage of Jasmine

Hobie20 from Eric Holmes on Vimeo.

We're Being Followed!

Often out on the bay, there are sea lions that appear in solo, team or larger group formations. The first time I saw these guys I thought they were Scuba Divers Surfacing all around me. I wonder what the Hobie hulls mean to these guys.

Hobie 20 Sailing in 2014 -- Sail Trim in Photos

Might make more way if I dropped the traveler car down a bit... [Photo: Jim Laws, IYC]

Sail trim can be tricky without an objective 3rd party watching from away from the boat. These photos are some records of 2014 races and trims. All are courtesy of IYC Member and Photographer Jim Laws.

More Forward Weight would prevent "Jasmine" from dragging her bottom in the water... [Photo: Jim Laws, IYC]

Sailing with a brand new Jib, "Jasmine" responded well, winning 1 race and taking 3rd in another during the IYC 2014 season. I'm not sure why I'm grimacing in this photo, but with one hull completely flying, the boat is sailing pretty well in this shot. Wetted surface area is reduced and we're off.

More Crew/Skipper Weight Forward may help here. BUT: Burying the leeward hull a bit... [Photo: Jim Laws, IYC]

Catching a gust from the Estero, Jasmine dug her bow in, so a little weight aft kept her pretty balanced. Apparently, the optimum crew weight is 350lbs. for this boat.

Note the Broken Batten 4th from the top. This foiled some Tacks by preventing the main from "Popping Over" and has now been replaced.

Hobie 20 Lifting Harness and Spinnaker Planning

I use a four line harness to lift Jasmine [Hobie 20] into and out of the water. Here are the line lengths:

Lifting Line Lengths -> Hobie 20 Harness:
Front: 44.5 Inches + 72 Inch Loop [Ring to Ctr. of Bowline]
Rear: 77 Inches + 60 Inch Loop [Ring to Ctr. of Bowline]

I'm working with a sailmaker to spec. out a spinnaker, while at the same time designing a pole and snuffer system that will not get in the way of my existing rigging. It is proving quite a challenge.

Spinnaker References:
http://home.comcast.net/~ragenpl/nacra/NACRA_55_SLOOP_SPINNAKER_USING_INTER_20_SNUFFER.htm

http://www.theracingcat.com/index.php?page=spinnaker-rigging

Check out the "Hobie 20" page to the right for an updated BOM for my setup.

Kawasaki Concours Year 2001 -- Ride Quality

I've just finished my second ride on the Concours, and it feels like a cousin of the 2004 Kawasaki Ninja 636 that I used to own, except it is a lobos domesticado in comparison. Instead of the Fuel Injected, throttle position sensor driven, ram air aspirated Ninja, the Concours is carbureted and takes longer to warm up. It also took me a minute to remember the function of the choke. The bike stalls occasionally before warming up, and even when warmed up at idle. There are probably a few issues with the bike which is now about 13 years old. With less than 30K miles, it has not been ridden much. Nevertheless, the ride is very stable upto 85mph or so. I haven't really pushed it hard on the freeway, and honestly, it really isn't designed for 636 style performance. With its hard luggage hanging from each side and a 600 lb dry weight, the bike is a blue beast.

The instrument cluster is rather old-school but very clear and illuminated pretty well. The fairing has two small compartments, one on each side, which open with the same ignition key. The seat is comfortable. Overall the bike seems about what I expected, although I haven't yet been able to get 7 gallons in the tank. [Seems to max out at 4 -- perhaps I'm doing something wrong.] Assuming that the tank can hold that much fuel, it should approach 250-300 miles per tank.

Great Cupertino Weather: Boat Work and Cruising on a used Kawasaki Concours

Well, the season that I love Cupertino for is here -- fantastic weather for the weekend meant that I made an impulse purchase of a motorcycle that I've had my eye on for some time. The year 2000+ Kawasaki Concours. Before I give my impression of the first ride on this 4-carbureted big bike, I'll outline some other work that I've been doing today: tuning the Hobie 20 for race season.

I was hoping to get out for a sail today, but memories of flipping over last weekend, and a low tide kept me grounded today. Instead I decided to do some race-prep and rigging work.

Task 1: Replace the Jib Car Travel Wire with two swaged "Fork" style fittings. This has proved more expensive and harder to do than it should.

After some searching online, I saw this Swaging tutorial which I intend to follow for my 1/8 inch stainless wire rope. Although I have never seen hand-swage marks on the existing Hobie fittings, I think that these can essentially be crimped on. The fittings themselves are very expensive {$15 per fitting} and I ended up ordering these online at a site called Zoro.com.

• https://www.youtube.com/watch?v=pLUCYgGVL0I
• http://www.zorotools.com/
• Search Terms: 1/8" Wire Rope Fork End Fitting [The manufacturer is Loos]
• Another site selling the fitting: http://www.velasailingsupply.com/Navtec-Swage-Fork-1-8-Wire-1-4-Pin-p/nvn547-0408.htm 

Task 2: Now I need to replace a screw pin to my Jib Halyard shackle which has lost this for some reason. The small shackle is swaged onto wire rope, so I'm reluctant to replace the entire shackle unless I have to. I had pulled the wire rope halyard in favor of Spectra, but now I'm beginning to think that the wire rope, as small as it is, will more easily fit within the Jib Luff pocket. [I've had a lot of trouble raising/lowering the Hobie 20 Jib, possibly for this reason.] I hope to resolve this by finding some loose shackle pins among other odds and ends on my work bench.

Task 3: Measure the Hobie 20 for Spin. Haylard to Pole Tip [29 Ft] and Pole Tip to Turning Block Dimensions [18Ft]. I was able to get some idea of the first dimension based on having to drop my mast last weekend to retrieve the Main Halyard. The mast is 31 Ft 4" [measurement error?] and according the Barefoot Sailing's SNU guide, another Hobie 20 sailor succeeded with the Spin Halyard 5 feet from the mast-head. This would put the height from the Trampoline at 26 Ft or so. I measured the Forestay at 23 Ft 4" while taking the mast partially down. Another Hobie Document states that the Hobie 20 should have its Halyard Tang at 24-26" [Depending on Doc revision] from the start of the Comp Tip. That also comes out at 25 Ft + I would like to fly a large Assym, so 26 Ft is what I plan to use. A 12 Foot Pole is very long on a 20 Foot Long boat -- I am having second thoughts about using this length. The Hobie standard is apparently 11.5Ft.